Hi,

Is it possible to tweak some files to add a new platform and a new host to ESD software?
Because when I'm exporting sources, there are not my new platform dependent files.
I'm working on Renesas Synergy Platform.
I've edited EVE_config.h, target.config and export.config.

Or supported platforms are hardcoded in the ESD software?
thx.

thx for these precisions.

If I want to display an image 24 bits (compressed or not) which format is recommended for my 18 bits/pixel screen?
RGB565? Is there any loss of color information?

I've tried with a 16 bits image and RGB565 and gray part has turned blue on display. Why?

Hi,
I'd like to connect my screen with d0 to d17 data pins to BT816 chip.
So I have D17-D12 for Red, D11-D6 for Green and D5-D0 for blue, 6bits/color.
Which pins should I connect to BT816 R0 to R5 or R2 to R7?
If I remember I must set REG_OUTBITS to 0x01B6. Right?

Thanks.

Hi,

We have 2.8" screens with ILI9341 or ST7789 controllers.
Often they have no HSYNC, VSYNC, DE pins but D/C, WR, RD, CS,IM0-3  and RGB 16bits or 18 bits pin interface (D0-D15). D0 to D7 can be command or D0-D15 data.
Do you have a list of compatibility of controllers or screens for BT880?

It's a 2.8" with 320x240 landscape format. Controller is ILI9341 or ST7789 with 18bits RGB bus.

Has anyone ever tried to use them with ESD? If I choose BT880, what are the settings to configure for a new project if my mcu is STM32?

Thanks for your reply.

But if my system clock is 72MHz PCLK=8? or both work?

Hi,

I'm experiencing some glitches on my screen of my device sometimes.

Could you help me to set REG values for display initialization with attached files?

      PIXVOFFSET = ?
      PIXHOFFSET = ?
      HCYCLE = ?
      HOFFSET = ?
      HSYNC0 = ?
      HSYNC1 = ?
      VCYCLE = ?
      VOFFSET = ?
      VSYNC0 = ?
      VSYNC1 = ?
      PCLK = ?
      SWIZZLE = ?
      PCLK_POL = ?
      HSIZE = 480;   //ok
      VSIZE = 272;   //ok
      CSPREAD = ?
      DITHER = ?

System clock is 72MHz.

Thanks.

Hi?

I written in EVE flash blob file, map file and a zlib image that can be variable.

I inflate image in RAM_G, but when I use CMD_SETBITMAP to display it, I must know Height and Width properties that can be variables.

How can I get this properties, since CMD_GETPROPS doesn't work on  CMD_INFLATE but on CMD_LOADIMAGE??

Hi,

Any update on this?

Size of spinner depends from the size of the display. Is there a workaround to modify height and/or width temporarly to reduce its size?

No I'm using Renesas synergy platform and GNU GCC toolchain. I 've created a library project type to export in it, I'm using only msvc source code and it works anyway.

Hi,

Why this menu disappeared?
It was vvery helpfull for me. How can I do now with new version for eclipse project types?

regards

OK but whith this type I can't set alpha value in color picker window. Before, I could change it.

Hi,

I've just installed this version but I don't find ft_argb32_t type on selection list of a variable for example. Is it normal?


regards

Hi it's a Matrix Orbital 43A IPS with EVE3 BT815 chip.